pmlogger_daily_report(1) — Linux manual page
PMLOGGER_DAILY_REPORT(1) General Commands ManualPMLOGGER_DAILY_REPORT(1)
NAME
pmlogger_daily_report - write Performance Co-Pilot daily summary
reports
SYNOPSIS
$PCP_BINADM_DIR/pmlogger_daily_report [-ApV?] [-a archivefile]
[-f outputfile] [-h hostname] [-l logfile] [-o directory] [-t
interval]
DESCRIPTION
pmlogger_daily_report writes daily performance summary reports,
much like those produced by sadc(1) and the sa2(8) utility.
All of the command line arguments are optional and intended to be
self explanatory.
By default, the reports are not generated, but if the pcp-
zeroconf package has been installed (there will be files in
$PCP_VAR_DIR/config/pmlogconf/zeroconf) then the necessary
metrics will have been included in the default pmlogger(1)
configuration file and the reports will be generated.
The reports are generated (by default) soon after midnight, once
pmlogger_daily(1) has completed the merging of any partial
archives to generate one archive for yesterday's activity.
Each performance summary report is named sarXX (where XX is
yesterdays day-of-the-month). The outputfile may be changed with
the -f option. The report will be written to the $PCP_LOG_DIR/sa
directory by default, but this may be changed with the -o option
to a different directory.
Note that there are sufficiently flexible command line options
for pmlogger_daily_report to be used to read any archivefile and
write the report to any output directory.
If the -a option is not given, the default input archivefile is
$PCP_ARCHIVE_DIR/HOSTNAME/YYYYMMDD, where HOSTNAME defaults to
the local hostname (unless changed with the -h option) and
YYYYMMDD is the base name of yesterdays merged archive, as
produced by pmlogger(1) and pmlogger_daily(1). If archivefile is
a directory, then pmlogger_daily_report will use all PCP archives
found in that directory to write the report (this is known as
multi-archive mode, and may be considerably slower than
specifying a single archive as the input).
The reports themselves are created by the pmrep(1) utility using
its default configuration file, see pmrep.conf(5). The pmrep(1)
configuration entries used to write the reports is currently
hardwired into the pmlogger_daily_report script.
Finally, the input archives must contain sufficient metrics as
needed by pmrep(1) to write the report. On platforms that
support it, the pcp-zeroconf package configures PCP logging as
required for this - hence pmlogger_daily_report should be used
with the pmlogger(1) configuration that is set up by pcp-
zeroconf. As the name suggests, pcp-zeroconf requires no
additional configuration after installation in order to capture
the required archives needed by pmlogger_daily_report.
OPTIONS
The available command line options are:
-a archive
Specifies an alternate input archive file basename or
directory path.
-A Use the start and end times of input archive for the report,
as opposed to the default behaviour of 24 hours from
midnight yesterday.
-f filename
Specifies an alternate output filename. -h hostname
Specifies an alternate hostname to use within the default
input archive file path.
-l file, --logfile=file
In order to ensure that mail is not unintentionally sent
when this script is run from pmlogger_daily(1) diagnostics
are always sent to a log file. By default, this file is
$PCP_LOG_DIR/pmlogger/pmlogger_daily_report.log but this can
be changed using the -l option. If this log file already
exists when the script starts, it will be renamed with a
.prev suffix (overwriting any log file saved earlier) before
diagnostics are generated to the log file.
-p If this option is specified then the status of the daily
processing is polled and if the report has not been done in
the last 24 hours then it is done now. With this option,
pmlogger_daily_report simply exits if the previous day's
processing has already been done.
This option is no longer required as the polling of
pmlogger_daily(1) will ensure the report will be generated,
however the option is retained for backwards compatibility.
-t interval
Specifies the sampling interval used when generating the
report, in the format described in PCPIntro(1). The default
is every 10 minutes.
-V, --verbose
The output from the execution of the script may be extended
using this option which enables verbose tracing of activity.
By default the script generates no log output unless some
error or warning condition is encountered.
-?, --help
Display usage message and exit.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to
parameterize the file and directory names used by PCP. On each
installation, the file /etc/pcp.conf contains the local values
for these variables. The $PCP_CONF variable may be used to
specify an alternative configuration file, as described in
pcp.conf(5).
SEE ALSO
PCPIntro(1), pmlogger_daily(1), pmlogger(1), pmrep(1), sadc(1)
and sa2(8).
COLOPHON
This page is part of the PCP (Performance Co-Pilot) project.
Information about the project can be found at
⟨http://www.pcp.io/⟩. If you have a bug report for this manual
page, send it to pcp@groups.io. This page was obtained from the
project's upstream Git repository
⟨https://github.com/performancecopilot/pcp.git⟩ on 2024-06-14.
(At that time, the date of the most recent commit that was found
in the repository was 2024-06-14.) If you discover any rendering
problems in this HTML version of the page, or you believe there
is a better or more up-to-date source for the page, or you have
corrections or improvements to the information in this COLOPHON
(which is not part of the original manual page), send a mail to
man-pages@man7.org
Performance Co-Pilot PCP PMLOGGER_DAILY_REPORT(1)
Pages that refer to this page: pmlogger_check(1), pmlogger_daily(1), pmlogger.control(5)