preconv(1) — Linux manual page
preconv(1) General Commands Manual preconv(1)
Name
preconv - prepare files for typesetting with groff
Synopsis
preconv [-dr] [-D fallback-encoding] [-e encoding] [file ...]
preconv -h
preconv --help
preconv -v
preconv --version
Description
preconv reads each file, converts its encoded characters to a
form troff(1) can interpret, and sends the result to the standard
output stream. Currently, this means that code points in the
range 0–127 (in US-ASCII, ISO 8859, or Unicode) remain as-is and
the remainder are converted to the groff special character form
“\[uXXXX]”, where XXXX is a hexadecimal number of four to six
digits corresponding to a Unicode code point. By default,
preconv also inserts a roff .lf request at the beginning of each
file, identifying it for the benefit of later processing
(including diagnostic messages); the -r option suppresses this
behavior.
In typical usage scenarios, preconv need not be run directly;
instead it should be invoked with the -k or -K options of groff.
If no file operands are present, or if file is “-”, preconv reads
the standard input stream.
preconv selects an input encoding with the following algorithm,
stopping at the first success.
1. If the input encoding has been explicitly specified with
option -e, use it.
2. If the input starts with a Unicode Byte Order Mark, select
UTF-8, UTF-16, or UTF-32 accordingly.
3. If the input stream is seekable, check the first two input
lines for a GNU Emacs file-local variable identifying the
character encoding, here referred to as the “coding tag”. If
found, use it.
4. If the input stream is seekable, and if the uchardet library
is available on the system, use it to try to infer the
encoding of the file.
5. If the -D option specifies an encoding, use it.
6. Use the encoding specified by the current locale (LC_CTYPE),
unless the locale is “C”, “POSIX”, or empty, in which case
assume Latin-1 (ISO 8859-1).
The coding tag and uchardet methods in the above procedure rely
upon a seekable input stream; when preconv reads from a pipe, the
stream is not seekable, and these detection methods are skipped.
If character encoding detection of your input files is
unreliable, arrange for one of the other methods to succeed by
using preconv's -D or -e options, or by configuring your locale
appropriately. groff also supports a GROFF_ENCODING environment
variable, which can be overridden by its -K option. Valid values
for (or parameters to) all of these are enumerated in the lists
of recognized coding tags in the next subsection, and are further
influenced by iconv library support.
Coding tags
Text editors that support more than a single character encoding
need tags within the input files to mark the file's encoding.
While it is possible to guess the right input encoding with the
help of heuristics that produce good results for a preponderance
of natural language texts, they are not absolutely reliable.
Heuristics can fail on inputs that are too short or don't
represent a natural language.
Consequently, preconv supports the coding tag convention used by
GNU Emacs (with some restrictions). This notation appears in
specially marked regions of an input file designated for “file-
local variables”.
preconv interprets the following syntax if it occurs in a roff
comment in the first or second line of the input file. Both “\"”
and “\#” comment forms are recognized, but the control (or no-
break control) character must be the default and must begin the
line. Similarly, the escape character must be the default.
-*- [...;] coding: encoding[; ...] -*-
The only variable preconv interprets is “coding”, which can take
the values listed below.
The following list comprises all MIME “charset” parameter values
recognized, case-insensitively, by preconv.
big5, cp1047, euc-jp, euc-kr, gb2312, iso-8859-1,
iso-8859-2, iso-8859-5, iso-8859-7, iso-8859-9,
iso-8859-13, iso-8859-15, koi8-r, us-ascii, utf-8, utf-16,
utf-16be, utf-16le
In addition, the following list of other coding tags is
recognized, each of which is mapped to an appropriate value from
the list above.
ascii, chinese-big5, chinese-euc, chinese-iso-8bit,
cn-big5, cn-gb, cn-gb-2312, cp878, csascii, csisolatin1,
cyrillic-iso-8bit, cyrillic-koi8, euc-china, euc-cn,
euc-japan, euc-japan-1990, euc-korea, greek-iso-8bit,
iso-10646/utf8, iso-10646/utf-8, iso-latin-1, iso-latin-2,
iso-latin-5, iso-latin-7, iso-latin-9, japanese-euc,
japanese-iso-8bit, jis8, koi8, korean-euc,
korean-iso-8bit, latin-0, latin1, latin-1, latin-2,
latin-5, latin-7, latin-9, mule-utf-8, mule-utf-16,
mule-utf-16be, mule-utf-16-be,
mule-utf-16be-with-signature, mule-utf-16le,
mule-utf-16-le, mule-utf-16le-with-signature, utf8,
utf-16-be, utf-16-be-with-signature,
utf-16be-with-signature, utf-16-le,
utf-16-le-with-signature, utf-16le-with-signature
Any “-dos”, “-unix”, or “-mac” suffix on a coding tag (which
indicates the end-of-line convention used in the file) is ignored
during comparison with the above tags.
[1miconv[24m support
While preconv recognizes all of the coding tags listed above, it
is capable on its own of interpreting only three encodings:
Latin-1, code page 1047, and UTF-8. If iconv support is
configured at compile time and available at run time, all others
are passed to iconv library functions, which may recognize many
additional encoding strings. The command “preconv -v” discloses
whether iconv support is configured.
The use of iconv means that characters in the input that encode
invalid code points for that encoding may be dropped from the
output stream or mapped to the Unicode replacement character
(U+FFFD). Compare the following examples using the input “café”
(note the “e” with an acute accent), which due to its short
length challenges inference of the encoding used.
printf 'caf\351\n' | LC_ALL=en_US.UTF-8 preconv
printf 'caf\351\n' | preconv -e us-ascii
printf 'caf\351\n' | preconv -e latin-1
The fate of the accented “e” differs in each case. In the first,
uchardet fails to detect an encoding (though the library on your
system may behave differently) and preconv falls back to the
locale settings, where octal 351 starts an incomplete UTF-8
sequence and results in the Unicode replacement character. In
the second, it is not a representable character in the declared
input encoding of US-ASCII and is discarded by iconv. In the
last, it is correctly detected and mapped.
Limitations
preconv cannot perform any transformation on input that it cannot
see. Examples include files that are interpolated by
preprocessors that run subsequently, including soelim(1); files
included by troff itself through “so” and similar requests; and
string definitions passed to troff through its -d command-line
option.
preconv assumes that its input uses the default escape character,
a backslash \, and writes special character escape sequences
accordingly.
Options
-h and --help display a usage message, while -v and --version
show version and configuration information; all exit afterward.
-d Emit debugging messages to the standard error stream.
-D fbenc
Select the fallback encoding fbenc if all detection
methods fail.
-e enc Skip detection and select encoding enc; see groff's -K
option.
-r Write files “raw”; do not add .lf requests.
See also
groff(1), iconv(3), locale(7)
COLOPHON
This page is part of the groff (GNU troff) project. Information
about the project can be found at
⟨http://www.gnu.org/software/groff/⟩. If you have a bug report
for this manual page, see ⟨http://www.gnu.org/software/groff/⟩.
This page was obtained from the project's upstream Git repository
⟨https://git.savannah.gnu.org/git/groff.git⟩ on 2024-06-14. (At
that time, the date of the most recent commit that was found in
the repository was 2024-06-10.) If you discover any rendering
problems in this HTML version of the page, or you believe there
is a better or more up-to-date source for the page, or you have
corrections or improvements to the information in this COLOPHON
(which is not part of the original manual page), send a mail to
man-pages@man7.org
groff 1.23.0.1273-9d53-dirty 6 June 2024 preconv(1)
Pages that refer to this page: groff(1)