Home Improvement Stack Exchange
Home Improvement Stack Exchange

Questions tagged [circular-saw]

79 questions
21
votes
4 answers

Setting cut depth on a circular saw

When using a circular saw to cut through panels or dimensional lumber or whatever, the DIY folk on YouTube always set the cut depth to “a hair beyond what you’re cutting”. I’ve been blindly doing the same, but realized the other day I have no idea…
Rob de Jonge
  • 743
  • 2
  • 10
  • 21
19
votes
4 answers

Is this saw blade faulty?

This may be the stupidest DIY question ever, but I want to make sure before I return it: is this non-ferrous metals saw blade faulty? In the picture, see where one of the titanium carbide teeth seems to be too large and to extend into the expansion…
RustyShackleford
  • 2,777
  • 5
  • 40
  • 61
12
votes
7 answers

What tool should I use to remove this screw in my miter saw motor housing?

I have a miter saw from the company "Elektra Beckum", which went out of business several years ago. The saw worked flawlessly until my house got flooded last summer. Now I had the time to clean it. The saw runs again, but it is very loud. I want to…
steloe
  • 223
  • 1
  • 4
8
votes
8 answers

Why won't my circular saw blade tighten on the spindle?

The blade on my Craftsman circular saw will not tighten down and consequently slips on the spindle. I've tried packing the bolt with a washer and it didn't help. Can't find anything online so this may not be a typical problem. Could it be as…
Robert Jolly
  • 81
  • 1
  • 1
  • 2
7
votes
5 answers

Where is the blade/spindle lock on an old Skilsaw 5250 7 1/4" circular saw?

I have a Skilsaw 5250 7 1/4" circular saw i picked up used 20 years ago. No idea how old it is, but still works. I recently put a metal grinding blade on it to cut roofing tin. Worked great. But now I want to put the saw blade back on. Never saw a…
Michael
  • 71
  • 1
  • 2
7
votes
4 answers

Why does a cordless circular saw have the blade on the left?

At the moment considering the purchase of a circular saw for light work. I'm looking at a corded model and a cordless model. But the question I have is not about which one is better. My question today is why the corded one has the blade on the…
Rob de Jonge
  • 743
  • 2
  • 10
  • 21
6
votes
4 answers

How to safely route a wide groove in 2x2?

I would like to create a groove 3/4" wide and 1" deep in a piece of red oak 2x2, approximately 5" long (it is being sized to slip over a 1x2). I have a 1/2" router bit, and have successfully created a 1/2" wide, 1" deep groove in the piece; when I…
kyle
  • 184
  • 3
  • 9
5
votes
3 answers

Is a special circular saw blade needed to cut plastic?

We purchased two portable air conditioners for our bedrooms. It include a plastic window kit that can be fitted for the window. I.e., this: I need to trim off about 6 inches, which requires a simple straight cut. Doing it by hand is challenging…
Bill
  • 407
  • 1
  • 5
  • 9
4
votes
3 answers

Beginner friendly pocket cuts

I need to make a cut about 24" long x 5" wide inside of a longer piece of common board 1x12x~7ft. So basically cutting out a smaller rectangle inside a bigger rectangular piece of wood. I believe this is called a pocket cut since it does not extend…
Dan
  • 73
  • 1
  • 7
4
votes
6 answers

Cutting a 4.5m long 2x6 in half with a circular saw

My question is about cutting 2x6 boards in half with a circular saw ("Skil"-saw). Now, I've looked around, and there are many sites describing how to cut off a small piece from a larger piece, the latter you want to keep. Most of them point out that…
Yishai E
  • 143
  • 1
  • 5
4
votes
1 answer

Can i use larger/smaller circular saw blades on my circular / plunge / table / miter saw?

I own a plunge saw and a miter saw. Can I use blades from one saw on the other saw?
maddrag0n
  • 241
  • 1
  • 2
  • 4
3
votes
2 answers

Can I use a jigsaw to cut fence rails?

I'm looking for a saw to complete my fencing project. I was using a circular saw to cut the fence rails but it went for a walk, if you know what I mean. I'm now wondering if a jigsaw would be a worth getting instead of another circular saw because…
There is no spoon
  • 143
  • 1
  • 4
3
votes
4 answers

how to fix blade wobble in circular saw

The blade on my Skilsaw model 5150 wobbles quite a bit. I can tell the wobble is coming from the shaft itself. (I can grab the shaft and wiggle it around quite a bit --- the result of the "looseness" in the shaft is about a 3/16" wobble on the rim…
Zack
  • 31
  • 1
  • 1
  • 2
3
votes
1 answer

Circular saw drift

This seems to happen on every cut I make, whatever material, width or depth of cut Clamp down guide piece. No lateral movement. Start cut flat and straight. The front of the baseplate stays tight to the guide, the rear drifts out maybe up to 1/4…
999frogs
  • 33
  • 3
3
votes
5 answers

Dewalt DCS391 - Can't change blade on circular saw because of stuck blade clamping screw

I need to change the blade on my Dewalt DCS391 circular saw for the first time. The blade clamping screw is for an hex key left-hand threads, but I can't unfreeze it no matter how much lever of pressure I put on it, I'm starting to eat the screw…
Maxime Poulin
  • 91
  • 1
  • 2
  • 8
1
2 3 4 5 6